vyos_interfaces – Manages interface attributes of VyOS network devices¶

New in version 2.9.

Synopsis
Parameters
Notes
Examples
Return Values
Status

Synopsis ¶

This module manages the interface attributes on VyOS network devices.
This module supports managing base attributes of Ethernet, Bonding, VXLAN, Loopback and Virtual Tunnel Interfaces.

Parameters ¶

Parameter			Choices/Defaults	Comments
config list				The provided interfaces configuration.
	description string			Interface description.
	duplex string		Choices: full half auto	Interface duplex mode. Applicable for Ethernet interfaces only.
	enabled boolean		Choices: no yes ←	Administrative state of the interface. Set the value to `true` to administratively enable the interface or `false` to disable it.
	mtu integer			MTU for a specific interface. Refer to vendor documentation for valid values. Applicable for Ethernet, Bonding, VXLAN and Virtual Tunnel interfaces.
	name string / required			Full name of the interface, e.g. eth0, eth1, bond0, vti1, vxlan2.
	speed string		Choices: auto 10 100 1000 2500 10000	Interface link speed. Applicable for Ethernet interfaces only.
	vifs list			Virtual sub-interfaces related configuration. 802.1Q VLAN interfaces are represented as virtual sub-interfaces in VyOS.
		description string		Virtual sub-interface description.
		enabled boolean	Choices: no yes ←	Administrative state of the virtual sub-interface. Set the value to `true` to administratively enable the interface or `false` to disable it.
		mtu integer		MTU for the virtual sub-interface. Refer to vendor documentation for valid values.
		vlan_id integer		Identifier for the virtual sub-interface.
state string			Choices: merged ← replaced overridden deleted	The state of the configuration after module completion.

Notes ¶

Note

Tested against VyOS 1.1.8 (helium).
This module works with connection network_cli. See the VyOS OS Platform Options.

Examples ¶

# Using merged
#
# -------------
# Before state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo

- name: Merge provided configuration with device configuration
  vyos_interfaces:
    config:
      - name: eth2
        description: 'Configured by Ansible'
        enabled: True
        vifs:
          - vlan_id: 200
            description: "VIF 200 - ETH2"

      - name: eth3
        description: 'Configured by Ansible'
        mtu: 1500

      - name: bond1
        description: 'Bond - 1'
        mtu: 1200

      - name: vti2
        description: 'VTI - 2'
        enabled: false
    state: merged
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
# "before": [
#           {
#            "enabled": true,
#            "name": "lo"
#           },
#       {
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "enabled": true,
#            "name": "eth2"
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "set interfaces ethernet eth2 description 'Configured by Ansible'",
#        "set interfaces ethernet eth2 vif 200",
#        "set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'",
#        "set interfaces ethernet eth3 description 'Configured by Ansible'",
#        "set interfaces ethernet eth3 mtu '1500'",
#        "set interfaces bonding bond1",
#        "set interfaces bonding bond1 description 'Bond - 1'",
#        "set interfaces bonding bond1 mtu '1200'",
#        "set interfaces vti vti2",
#        "set interfaces vti vti2 description 'VTI - 2'",
#        "set interfaces vti vti2 disable"
#    ]
#
# "after": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1200,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "VTI - 2",
#            "enabled": false,
#            "name": "vti2"
#        },
#        {
#            "description": "Configured by Ansible",
#            "enabled": true,
#            "mtu": 1500,
#            "name": "eth3"
#        },
#        {
#            "description": "Configured by Ansible",
#            "enabled": true,
#            "name": "eth2",
#            "vifs": [
#                {
#                    "description": "VIF 200 - ETH2",
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# -------------
# After state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1200'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces loopback lo
# set interfaces vti vti2 description 'VTI - 2'
# set interfaces vti vti2 disable
#


# Using replaced
#
# -------------
# Before state:
# -------------
#
# vyos:~$ show configuration commands | grep eth
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:f3:6c:b5'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ad:ef:65'
# set interfaces ethernet eth1 smp_affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:ab:4e:79'
# set interfaces ethernet eth2 mtu '500'
# set interfaces ethernet eth2 smp_affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth2 vif 200 description 'Configured by Ansible'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:17:3c:85'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces ethernet eth3 smp_affinity 'auto'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo
#
#
- name: Replace device configurations of listed interfaces with provided configurations
  vyos_interfaces:
    config:
      - name: eth2
        description: "Replaced by Ansible"

      - name: eth3
        description: "Replaced by Ansible"

      - name: eth1
        description: "Replaced by Ansible"
    state: replaced
#
#
# -----------------------
# Module Execution Result
# -----------------------
#
# "before": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1400,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": true,
#            "mtu": 1500,
#            "name": "eth3",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": true,
#            "mtu": 500,
#            "name": "eth2",
#            "speed": "100",
#            "vifs": [
#                {
#                    "description": "VIF 200 - ETH2",
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "description": "Configured by Ansible Eng Team",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth1",
#            "speed": "100"
#        },
#        {
#            "description": "Management Interface for the Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces ethernet eth2 speed",
#        "delete interfaces ethernet eth2 duplex",
#        "delete interfaces ethernet eth2 mtu",
#        "delete interfaces ethernet eth2 vif 200 description",
#        "set interfaces ethernet eth2 description 'Replaced by Ansible'",
#        "delete interfaces ethernet eth3 speed",
#        "delete interfaces ethernet eth3 duplex",
#        "delete interfaces ethernet eth3 mtu",
#        "set interfaces ethernet eth3 description 'Replaced by Ansible'",
#        "delete interfaces ethernet eth1 speed",
#        "delete interfaces ethernet eth1 duplex",
#        "set interfaces ethernet eth1 description 'Replaced by Ansible'"
#    ]
#
# "after": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1400,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth2",
#            "vifs": [
#                {
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "description": "Management Interface for the Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# -------------
# After state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Replaced by Ansible'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Replaced by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200
# set interfaces ethernet eth3 description 'Replaced by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
#
#
# Using overridden
#
#
# --------------
# Before state
# --------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Ethernet Interface - 0'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 mtu '1200'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 mtu '100'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100 description 'VIF 100 - ETH1'
# set interfaces ethernet eth1 vif 100 disable
# set interfaces ethernet eth2 description 'Configured by Ansible Team (Admin Down)'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
# set interfaces vti vti1 description 'Virtual Tunnel Interface - 1'
# set interfaces vti vti1 mtu '68'
#
#
- name: Overrides all device configuration with provided configuration
  vyos_interfaces:
    config:
      - name: eth0
        description: Outbound Interface For The Appliance
        speed: auto
        duplex: auto

      - name: eth2
        speed: auto
        duplex: auto

      - name: eth3
        mtu: 1200
    state: overridden
#
#
# ------------------------
# Module Execution Result
# ------------------------
#
# "before": [
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Virtual Tunnel Interface - 1",
#            "enabled": true,
#            "mtu": 68,
#            "name": "vti1"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "description": "Configured by Ansible Team (Admin Down)",
#            "enabled": false,
#            "mtu": 600,
#            "name": "eth2"
#        },
#        {
#            "description": "Configured by Ansible Eng Team",
#            "enabled": true,
#            "mtu": 100,
#            "name": "eth1",
#            "vifs": [
#                {
#                    "description": "VIF 100 - ETH1",
#                    "enabled": false,
#                    "vlan_id": "100"
#                }
#            ]
#        },
#        {
#            "description": "Ethernet Interface - 0",
#            "duplex": "auto",
#            "enabled": true,
#            "mtu": 1200,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces vti vti1 description",
#        "delete interfaces vti vti1 mtu",
#        "delete interfaces ethernet eth1 description",
#        "delete interfaces ethernet eth1 mtu",
#        "delete interfaces ethernet eth1 vif 100 description",
#        "delete interfaces ethernet eth1 vif 100 disable",
#        "delete interfaces ethernet eth0 mtu",
#        "set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'",
#        "delete interfaces ethernet eth2 description",
#        "delete interfaces ethernet eth2 mtu",
#        "set interfaces ethernet eth2 duplex 'auto'",
#        "delete interfaces ethernet eth2 disable",
#        "set interfaces ethernet eth2 speed 'auto'",
#        "delete interfaces ethernet eth3 description",
#        "set interfaces ethernet eth3 mtu '1200'"
#    ],
#
# "after": [
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "enabled": true,
#            "name": "vti1"
#        },
#        {
#            "enabled": true,
#            "mtu": 1200,
#            "name": "eth3"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth2",
#            "speed": "auto"
#        },
#        {
#            "enabled": true,
#            "name": "eth1",
#            "vifs": [
#                {
#                    "enabled": true,
#                    "vlan_id": "100"
#                }
#            ]
#        },
#        {
#            "description": "Outbound Interface For The Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# ------------
# After state
# ------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100
# set interfaces ethernet eth2 duplex 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1200'
# set interfaces loopback lo
# set interfaces vti vti1
#
#
# Using deleted
#
#
# -------------
# Before state
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1 description 'LAG - 1'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Network'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo
#
#
- name: Delete attributes of given interfaces (Note - This won't delete the interfaces themselves)
  vyos_interfaces:
    config:
      - name: bond1

      - name: eth1

      - name: eth2

      - name: eth3
    state: deleted
#
#
# ------------------------
# Module Execution Results
# ------------------------
#
# "before": [
#        {
#            "enabled": true,
#            "mtu": 1300,
#            "name": "bond0"
#        },
#        {
#            "description": "LAG - 1",
#            "enabled": true,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth3",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": false,
#            "mtu": 600,
#            "name": "eth2",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth1",
#            "speed": "100"
#        },
#        {
#            "description": "Outbound Interface for this appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces bonding bond1 description",
#        "delete interfaces ethernet eth1 speed",
#        "delete interfaces ethernet eth1 duplex",
#        "delete interfaces ethernet eth1 description",
#        "delete interfaces ethernet eth2 speed",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 duplex",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 description",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 mtu",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth3 speed",
#        "delete interfaces ethernet eth3 duplex",
#        "delete interfaces ethernet eth3 description"
#    ]
#
# "after": [
#        {
#            "enabled": true,
#            "mtu": 1300,
#            "name": "bond0"
#        },
#        {
#            "enabled": true,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "enabled": true,
#            "name": "eth2"
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "description": "Outbound Interface for this appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# ------------
# After state
# ------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
#
#

Return Values ¶

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
after list	when changed	The configuration as structured data after module completion. Sample: The configuration returned will always be in the same format of the parameters above.
before list	always	The configuration as structured data prior to module invocation. Sample: The configuration returned will always be in the same format of the parameters above.
commands list	always	The set of commands pushed to the remote device. Sample: ['set interfaces ethernet eth1 mtu 1200', 'set interfaces ethernet eth2 vif 100 description VIF 100']

Status ¶

This module is not guaranteed to have a backwards compatible interface. [preview]
This module is maintained by the Ansible Network Team. [network]

Red Hat Support¶

More information about Red Hat’s support of this module is available from this Red Hat Knowledge Base article.

Authors¶

Nilashish Chakraborty (@nilashishc)

Hint

If you notice any issues in this documentation, you can edit this document to improve it.

vyos_interfaces – Manages interface attributes of VyOS network devices¶

Synopsis¶

Parameters¶

Notes¶

Examples¶

Return Values¶

Status¶